全國免費招商熱線: 400-800-4491
產品咨詢訂購電話: 134-1834-4523
 當前位置:模具防銹劑首頁 - 新聞動態 - 技術分享 - 模具維修

塑料模具專業英語

發布時間:2016.09.24 新聞來源:脫模劑_防銹劑_清洗劑_頂針油_深圳金利源精細科技有限公司

模具述語

一、入水:gate

進入位: gate location

水口形式:gate type

大水口:edge gate

細水口: pin-point gate

水口大小:gate size

轉水口: switching runner/gate

唧嘴口徑: sprue diameter

二、流道: runner

熱流道: hot runner,hot manifold

熱嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圓形流道:round(full/half runner

流道電腦分析:mold flow analysis

流道平衡:runner balance

熱嘴: hot sprue

熱流道板:hot manifold

發熱管:cartridge heater

探針: thermocouples

插頭: connector plug

插座: connector socket

密封/封料: seal

三、運水:water line

喉塞:line lpug

喉管:tube

塑膠管:plastic tube

快速接頭:jiffy quick connector plug/socker

四、模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

邊釘/導邊:leader pin/guide pin

邊司/導套:bushing/guide bushing

中托司:shoulder guide bushing

中托邊L:guide pin

頂針板:ejector retainner plate

托板: support plate

螺絲: screw

管釘:dowel pin

開模槽:ply bar scot

內模管位:core/cavity inter-lock

頂針: ejector pin

司筒:ejector sleeve

司筒針:ejector pin

推板:stripper plate

縮呵:movable core,return core core puller

扣機(尼龍拉勾):nylon latch lock

斜頂:lifter

模胚(架): mold base

上內模:cavity insert

下內模:core insert

行位(滑塊): slide

鑲件:insert

壓座/斜雞:wedge

耐磨板/油板:wedge wear plate

壓條:plate

撐頭: support pillar

唧嘴: sprue bushing

擋板:stop plate

定位圈:locating ring

鎖扣:latch

扣雞:parting lock set

推桿:push bar

栓打螺絲:S.H.S.B

頂板:eracuretun

活動臂:lever arm

分流錐:spure sperader

水口司:bush

垃圾釘:stop pin

隔片:buffle

彈弓柱:spring rod

彈弓:die spring

中托司:ejector guide bush

中托邊:ejector guide pin

鑲針:pin

銷子:dowel pin

波子彈弓:ball catch

喉塞: pipe plug

鎖模塊:lock plate

斜頂:angle from pin

斜頂桿:angle ejector rod

尼龍拉勾:parting locks

活動臂:lever arm

復位鍵、提前回桿:early return bar

氣閥:valves

斜導邊:angle pin

術語:terms

承壓平面平衡:parting surface support balance

模排氣:parting line venting

回針碰料位:return pin and cavity interference

模總高超出啤機規格:mold base shut hight

頂針碰運水:water line interferes withejector pin

料位出上/下模:part from cavith (core)side

模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

不準用鑲件: Do not use (core/cavity) insert

用鈹銅做鑲件: use beryllium copper insert

初步(正式)模圖設計:preliinary (final) mold design

反呵:reverse core

彈弓壓縮量:spring compressed length

穩定性好:good stability,stable

強度不夠:insufficient rigidity

均勻冷卻:even cooling

扣模:sticking

熱膨脹:thero expansion

公差:tolorance

銅公(電極):copper electrode



Tags: 塑料 模具 英語 脫模劑
彩票开奖结果查绚